Differences

This shows you the differences between two versions of the page.

--- mangopi_r [2021/02/09 17:19]
admin [进阶/玩法]
+++ mangopi_r [2023/12/07 07:02] (current)
admin
@@ Line 1: / Line 1: @@
-=====MPi-R1/R2/R3=====
+~~NOTOC~~
-MPi-Rx（原TINY200）是针对全志超低价F1C200s设计的小型ARM-Linux原型板，一体化设计，迷你, 资源：
-  - USB-TTL CP2104串口控制台（开发必备）
-  - microUSB OTG口（fel方式刷机、接U盘、键盘、摄像头、usb网卡等）
-  - 16M nor FLASH 或者 128M nand flash
-  - TF卡槽，可接TF卡或TF-WiFi
-  - 40P通用RGB FPC排座<wrap hi>下接触</wrap>
-  - 板载电阻触摸芯片NS2009
-  - 6P通用电容触摸FPC排座
-  - 板载MIC*1
-  - BOOT按键、复位按键
-  - 5x2.2cm纤瘦尺寸，2.54排针引出所有资源，双排针间隔20.32mm适合面包板
-  - 24Pin DVP接口(only R2 R3)
-  - D类音频功放（only R2 R3）
-{{::mpi-r3-1.png?400|}}   {{::mpi-r3-2.png?400|}}
+{{::r3c-top.jpg?400  |}} {{  ::r3c-bot.jpg?400  |  }}
-  R1（首次发布，可搭配电阻触摸屏）
+=====Introduction=====
-  R2（在R1基础上增加DVP接口和音频功放）
-  R3（修复R2的触摸中断，新增电容触摸屏及Buildroot支持）
-<WRAP group>
+This micro development board is specially designed to run Linux. Despite a mini body, it has all the vital functions. Equipped with F1C200S as the maincontroller chip, the board offers various commonly-used peripheral ports: GPIO, I2C & SPI, SDIO, Audio port(record, play), Video(RGB565 Display, touch, DVP), USB Host, OTG, etc. Besides, the board comes with a built-in 64MB DDR and onboard 128MB Nand Flash, which fully supports Linux ecology and running complete Python.
-=====Buildroot on Tiny200支持情况=====
-<WRAP half column>
-====正常&测试====
-=== 启动项: ===
-  * SPI NOR Flash (W25Qxx..)
-  * SPI NAND Flash (GD5F1GQ4UAxxG..)
-  * MMC 0 (4-bit TF卡或芯片)
-  * MMC 1 (1-bit TF芯片，雷龙)
-=== U-Boot: ===
-  * Basic LCD/GPIO背光
-  * SF Devices
-  * MTD Devices
-  * USB Peripheral
-  * USB Mass Storage Drive Enulator
-  * DFU下载方式
-  * TF卡刷方式
-=== Linux:===
-  * Simple Peripheral: GPIO, SPI, UART, IIC, SDIO, PWM
-  * DMA Controller
-  * Audio Codec: Playback, Mic-IN
-  * USB: OTG Mode, Peripheral Mode, Host Mode
-  * DVP Camera: OV2640, OV5640
-  * Display Engine: Frontend, Backend, TCON
-  * Keypad ADC
-  * AW9523B GPIO扩展
-  * AXP199
-</WRAP>
-<WRAP half column>
-==== 正常&未测试====
-U-Boot 驱动:
-  * PWM Backlight
-Linux 驱动:
-  * Audio Codec: FM-IN, Line-IN
-  * IR Receiver
-  * Cedar Video Engine
-==== 正在开发====
-Linux 驱动:
-  * TV(CVBS) En/De
-</WRAP>
-</WRAP>
+=====Specification=====
+  * Built-in 64MB DDR
+  * On-board 128MB Nand Flash
+  * 420MHz system clock default frequency, able to be overclocked to 700MHz and above
+  * Rich GPIO pins
+  * Onboard SDIO port for connecting SD card or SDIO WiFi + BT module
+  * DVP camera interface in support of cameras such as OV2640, GC0328, etc.
+  * RGB565 display interface and 6-wire touch interface
+  * Onboard mic and power amplifier
+  * Low power consumption
+  * Support complete Python running
-----
+=====Getting Start=====
-<WRAP group>
+  * https://wiki.dfrobot.com/MangoPi_R3_SKU_DFR0780
-<WRAP half column>
-=====硬件=====
-  * [[f1c200_chip|F1C100s/F1C200s芯片资料]]
-  * [[TINY200|硬件资料]]
-  * [[1bittf|SPI位置使用1Bit-TF芯片]]
+=====MPi-R1/2/3/3c=====
-</WRAP>
+  * R1 (first commmit)
+  * R2 (added DVP and audio amp vs R1）
+  * R3 (fix R2 rtp interrupt, added ctp and buildroot, Mainly the nand version)
+  * R3c (change to ch340e from CP2104 vs R3)
-<WRAP half column>
-=====固件=====
-  * [[mpi-firmware|固件]]
-</WRAP>
-</WRAP>
-<WRAP group>
-<WRAP half column>
-=====环境=====
-  * [[f1c_br|Buildroot环境搭建]]
-  * [[f1c_mainline|编译]]
-</WRAP>
-<WRAP half column>
-=====刷机=====
-  * [[f1c_flashrom|刷机准备]]
-  * [[tinyflash|NOR Flash刷机]]
-  * [[f1c_nand|NandFlash刷机]]
-  * [[f1c_log|启动LOG]]
-</WRAP>
-</WRAP>
-=====进阶/玩法=====
-<WRAP group>
-<WRAP half column>
-  * [[f1c_source|源码目录]]
-  * [[f1c_play|F1C玩法介绍]]
-</WRAP>
-<WRAP half column>
-  * [[f1c_noos|裸机]]
-</WRAP>
-</WRAP>
+=====More=====
+[[f1c200s]]