Differences

This shows you the differences between two versions of the page.

--- mangopi_r [2022/03/01 06:53] – [Test OK] admin
+++ mangopi_r [2025/10/14 06:22] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
+~~NOTOC~~
+{{::r3c-top.jpg?400  |}} {{  ::r3c-bot.jpg?400  |  }}
 =====Introduction=====
 This micro development board is specially designed to run Linux. Despite a mini body, it has all the vital functions. Equipped with F1C200S as the maincontroller chip, the board offers various commonly-used peripheral ports: GPIO, I2C & SPI, SDIO, Audio port(record, play), Video(RGB565 Display, touch, DVP), USB Host, OTG, etc. Besides, the board comes with a built-in 64MB DDR and onboard 128MB Nand Flash, which fully supports Linux ecology and running complete Python.
-Currently, this product is fully open source so that users are allowed to compile any module according to their own requirements. However, it’s mainly for Python developers and senior enthusiasts as it’s a little difficult to get started.
 =====Specification=====
@@ Line 16: / Line 18: @@
   * Low power consumption
   * Support complete Python running
 =====Getting Start=====
   * https://wiki.dfrobot.com/MangoPi_R3_SKU_DFR0780
-=====R3c=====
-{{::r3c-top.jpg?400|}}{{::r3c-bot.jpg?400|}}
 =====MPi-R1/2/3/3c=====
@@ Line 36: / Line 30: @@
-=====Buildroot=====
+=====More=====
+[[f1c200s]]
-====Test OK====
-=== SPL: ===
-  * SPI NOR Flash (W25Qxx..)
-  * SPI NAND Flash (GD5F1GQ4UAxxG..)
-  * MMC 0 (4-bit TF)
-  * MMC 1 (1-bit TF)
-=== U-Boot: ===
-  * Basic LCD/GPIO背光
-  * SF Devices
-  * MTD Devices
-  * USB Peripheral
-  * USB Mass Storage Drive Enulator
-  * DFU
-  * TF
-=== Linux:===
-  * Simple Peripheral: GPIO, SPI, UART, IIC, SDIO, PWM
-  * DMA Controller
-  * Audio Codec: Playback, Mic-IN
-  * USB: OTG Mode, Peripheral Mode, Host Mode
-  * DVP Camera: OV2640, OV5640
-  * Display Engine: Frontend, Backend, TCON
-  * Keypad ADC
-  * AW9523B GPIO Expand
-----
-<WRAP group>
-<WRAP half column>
-=====Hardware=====
-  * [[f1c200_chip|F1C100s/F1C200s Chip]]
-  * [[TINY200|Hardware]]
-</WRAP>
-<WRAP half column>
-=====Firmware=====
-20210511,username: root , nopasswd
-  * NAND: {{ ::sysimage-nand-120mb.zip |}}
-  * NOR:  {{ ::sysimage-nor.zip |}}
-  * SDCARD: {{ ::r3-sdcard-20220130.zip |}}
-</WRAP>
-</WRAP>
-<WRAP group>
-<WRAP half column>
-=====Develop=====
-  * [[f1c_br|Buildroot env]]
-  * [[f1c_mainline|compile]]
-</WRAP>
-<WRAP half column>
-=====Manual=====
-  * [[https://wiki.dfrobot.com/MangoPi_R3_SKU_DFR0780|DFrobot Manual]]
-</WRAP>
-</WRAP>