Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
mangopi_r [2021/02/09 17:18] admin [进阶] |
mangopi_r [2022/03/15 09:55] admin |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | =====MPi-R1/ | + | {{::r3c-top.jpg? |
- | MPi-Rx(原TINY200)是针对全志超低价F1C200s设计的小型ARM-Linux原型板,一体化设计,迷你, | + | |
- | - USB-TTL CP2104串口控制台(开发必备) | + | |
- | | + | |
- | - 16M nor FLASH 或者 128M nand flash | + | |
- | - TF卡槽,可接TF卡或TF-WiFi | + | |
- | - 40P通用RGB FPC排座< | + | |
- | - 板载电阻触摸芯片NS2009 | + | |
- | - 6P通用电容触摸FPC排座 | + | |
- | - 板载MIC*1 | + | |
- | - BOOT按键、复位按键 | + | |
- | - 5x2.2cm纤瘦尺寸,2.54排针引出所有资源,双排针间隔20.32mm适合面包板 | + | |
- | - 24Pin DVP接口(only R2 R3) | + | |
- | - D类音频功放(only R2 R3) | + | |
- | {{:: | + | =====Introduction===== |
- | R1(首次发布,可搭配电阻触摸屏) | + | This micro development board is specially designed to run Linux. Despite a mini body, it has all the vital functions. Equipped with F1C200S as the maincontroller chip, the board offers various commonly-used peripheral ports: GPIO, I2C & SPI, SDIO, Audio port(record, |
- | R2(在R1基础上增加DVP接口和音频功放) | + | |
- | R3(修复R2的触摸中断,新增电容触摸屏及Buildroot支持) | + | |
- | <WRAP group> | + | =====Specification===== |
- | =====Buildroot on Tiny200支持情况===== | + | * Built-in 64MB DDR |
- | <WRAP half column> | + | * On-board 128MB Nand Flash |
- | ====正常& | + | * 420MHz system clock default frequency, able to be overclocked to 700MHz and above |
- | === 启动项: | + | * Rich GPIO pins |
- | * SPI NOR Flash (W25Qxx..) | + | * Onboard |
- | * SPI NAND Flash (GD5F1GQ4UAxxG..) | + | * DVP camera interface in support of cameras such as OV2640, |
- | * MMC 0 (4-bit TF卡或芯片) | + | * RGB565 display interface and 6-wire touch interface |
- | * MMC 1 (1-bit TF芯片,雷龙) | + | * Onboard mic and power amplifier |
- | === U-Boot: === | + | * Low power consumption |
- | * Basic LCD/GPIO背光 | + | * Support complete Python running |
- | * SF Devices | + | |
- | * MTD Devices | + | |
- | * USB Peripheral | + | |
- | * USB Mass Storage Drive Enulator | + | |
- | * DFU下载方式 | + | |
- | * TF卡刷方式 | + | |
- | === Linux:=== | + | |
- | * Simple Peripheral: GPIO, SPI, UART, IIC, SDIO, PWM | + | |
- | * DMA Controller | + | |
- | * Audio Codec: Playback, Mic-IN | + | |
- | * USB: OTG Mode, Peripheral Mode, Host Mode | + | |
- | * DVP Camera: | + | |
- | * Display Engine: Frontend, Backend, TCON | + | |
- | * Keypad ADC | + | |
- | * AW9523B GPIO扩展 | + | |
- | * AXP199 | + | |
- | </ | + | |
- | <WRAP half column> | + | |
- | ==== 正常& | + | |
- | U-Boot 驱动: | + | |
- | * PWM Backlight | + | |
- | Linux 驱动: | + | |
- | * Audio Codec: FM-IN, Line-IN | + | |
- | * IR Receiver | + | |
- | * Cedar Video Engine | + | |
- | ==== 正在开发==== | + | |
- | Linux 驱动: | + | |
- | * TV(CVBS) En/De | + | |
- | </ | + | |
- | </ | + | |
+ | =====Getting Start===== | ||
+ | * https:// | ||
- | ---- | + | =====MPi-R1/ |
- | <WRAP group> | + | * R1 (first commmit) |
- | <WRAP half column> | + | * R2 (added DVP and audio amp vs R1) |
- | =====硬件===== | + | * R3 (fix R2 rtp interrupt, added ctp and buildroot, Mainly the nand version) |
- | * [[f1c200_chip|F1C100s/ | + | * R3c (change to ch340e from CP2104 vs R3) |
- | * [[TINY200|硬件资料]] | + | |
- | * [[1bittf|SPI位置使用1Bit-TF芯片]] | ||
- | </ | ||
- | <WRAP half column> | + | =====More===== |
- | =====固件===== | + | [[f1c200s]] |
- | | + | |
- | </ | + | |
- | </ | + | |
- | |||
- | |||
- | <WRAP group> | ||
- | <WRAP half column> | ||
- | =====环境===== | ||
- | * [[f1c_br|Buildroot环境搭建]] | ||
- | * [[f1c_mainline|编译]] | ||
- | </ | ||
- | |||
- | <WRAP half column> | ||
- | =====刷机===== | ||
- | * [[f1c_flashrom|刷机准备]] | ||
- | * [[tinyflash|NOR Flash刷机]] | ||
- | * [[f1c_nand|NandFlash刷机]] | ||
- | * [[f1c_log|启动LOG]] | ||
- | </ | ||
- | </ | ||
- | |||
- | =====进阶/ | ||
- | |||
- | |||
- | |||
- | * [[f1c_play|F1C玩法介绍]] | ||